This wiki page allows you to record the results of your network configuration exercise. You may need to refer to the configuration handout to complete this document.

Answer all questions based on the host that you are configuring in the lab. Edit this wiki page directly to insert your answers. You will probably find this most convenient to do at the same time as you perform the configuration. Where requested, please include listings of the actual configuration files and command outputs directly in the document. Placeholders have been provided for this purpose. Please follow the formatting hints given in the text. Copy contents of file and paste it as a listing here.

Include a minumum indent of two spaces per line.
Like this. 

When the exercise is complete you should sign and submit it in for marking. Deadline for completion is the start of the lab on the last week of this term.

This exercise is worth 20% of the module marks.

Which Linux command gives you information about your computer's name on the network?

Answer: Copy contents of file and paste it as a listing here.

Include a minumum indent of two spaces per line.
Like this. 

 
 
hostname 

Use the command selected in Question 1 to determine your host computer's name? What is the name?

Answer:

icct@hyperion:~$ hostname
hyperion

Which configuration file would you need to edit to change your computer's name on the network?

Your answer:

/etc/hostname 

Copy contents of file and paste it as a listing here.

Include a minumum indent of two spaces per line.
Like this. 

Which linux command gives you information on your host's network settings?

Answer:

 
ifconfig 
  

Use the command selected in Question 4 to complete the following table:

     TX packets:5945 errors:0 dropped:0 overruns:0 carrier:0

How many hosts can the sub-net defined by your host's netmask support?

Answer one of:

254 

What class of network is the sub-net to which your host has been assigned?

Answer one of:

Class C

Answer the following questions about your network configuration. Please copy and paste the contents of the files identified in Questions 8 and 11 to your submission.

In which file is the configuration of your Network Interface Controller (NIC) configured?

Answer:

/etc/network/interfaces  

Please include a listing of the file chosen in answer to Question 8:

auto eth0
iface eth0 inet static
  address 192.168.3.2
  network 12.168.3.0
  netmask 255.255.255.0
  gateway 192.168.3.1

What is the IP address of the host which serves as the default gateway for your network?

Answer:

192.168.3.1

What is the hostname of the gateway interface?

Answer:

Saturn

In which file is the symbolic names of the networks, hosts and interfaces available on the network defined?

Answer one of:

/etc/hosts  

Please include a listing of the file chosen in answer to Question 11:

127.0.0.1	hyperion	localhost.localdomain	localhost
127.0.1.1	icct-desktop

# /etc/hosts -- Hosts file for ICCT Private network 
#
# IP         FQDN                      aliases
#
127.0.0.1    localhost.loclhostdomain      localhost hyperion
#
192.168.1.1   solaris.icct.com             solaris inet-gateway
192.168.1.2   venus.icct.com               venus www
#
# Jupiter cluster
#
192.168.1.3   gw-jupiter.icct.com          gw-planets jupiter-if1
192.168.2.1   jupiter.icct.com             jupiter jupiter-if2
192.168.2.2   ganymede.jupiter.icct.com    ganymede
192.168.2.3   leda.jupiter.icct.com        leda
192.168.2.4   carme.jupiter.icct.com       carme
192.168.2.5   arche.jupiter.icct.com       arche
#
# Saturn cluster
#
192.168.1.4   gw-saturn.icct.com           gw-saturn saturn-if1
192.168.3.1   saturn.icct.com              saturn saturn-if2
192.168.3.2   hyperion.saturn.icct.com     hyperion
192.168.3.3   mimas.saturn.icct.com        mimas
192.168.3.4   titan.saturn.icct.com        titan
192.168.3.5   tethys.saturn.icct.com       tethys
#
# Add other hosts/clusters below here
# (we'll use this to add virtual hosts to the web-server in a later
# lab exercise)

# The following lines are desirable for IPv6 capable hosts
::1     localhost ip6-localhost ip6-loopback
fe00::0 ip6-localnet
ff00::0 ip6-mcastprefix
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
ff02::3 ip6-allhosts

What is the symbolic name of your network's gateway interface?

Answer:

192.168.3.1   saturn.icct.com              saturn saturn-if2

What is the purpose of the Gateway interface?

Answer:

To provide a communication between the internet gateway and the networks.

Which linux command shows the routing table for your host?

Answer:

route

Run the command identified in Question 14 and reproduce its output here.

Answer

<cli prompt=“$” comment=“#”> icct@hyperion:~$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface saturn-net * 255.255.255.0 U 0 0 0 eth0 169.254.0.0 * 255.255.0.0 U 1000 0 0 eth0 default saturn.icct.com 0.0.0.0 UG 100 0 0 eth0

</cli>

How many interfaces (NICs) must a router have?

Answer one of:

2 

Which system feature must be turned on if you want a Linux host to act as a router?

Answer:

IP forwading

Which run-time command can be used to make a Ubuntu Linux host act as a router?

Answer:

sudo sh -c "echo > 1 /proc/sys/net/ipv4/ip_forward"

In which file is the setting defined in Question 17 set if you want a Ubuntu host to be configured as a router at boot-time?

Answer:

/etc/network/options

Reproduce the contents of the file defined in Question 17 to make a Ubuntu host into a router?

Answer

# /etc/network/options - for ICCT network
# set ip_forward=yes if you need to set
# up a machine with two network interface cards
# as a router
ip_forward=yes
spoofprotect=yes
syncookies=no

What setting has been added to the network configuration file to define a route to icct-net from your sub-network's cluster-server?

Answer:

up route add -net 192.168.2.0 netmask 255.255.255.0 gw 192.168.1.3
down route del -net 192.168.2.0 netmask 255.255.255.0 gw 192.168.1.3

The Linux command netstat gives a lot of useful information on your network. In the following 3 questions, reproduce the output of various usages of netstat. You should annotate your results with a brief explanation of what they mean. You may need to print the output and attach to the submission.

Give and explain the output of the command netstat -r.

Answer <cli prompt=“$” comment=“#”> icct@hyperion:~$ netstat -r

Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window  irtt Iface
saturn-net      *               255.255.255.0   U         0 0          0 eth0
169.254.0.0     *               255.255.0.0     U         0 0          0 eth0
default         saturn.icct.com 0.0.0.0         UG        0 0          0 eth0

</cli>

This command shows the routing tables.

Give and explain the output of the command netstat -i.

Answer <cli prompt=“$” comment=“#”> user@hyperion:~$ netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth0 1500 0 3196 0 0 0 2433 0 0 0 BMRU lo 16436 0 324 0 0 0 324 0 0 0 LRU

</cli>

This command shows the configured network interfaces.

Give and explain the output of the command netstat -ta.

Answer <cli prompt=“$” comment=“#”> user@hyperion:~$ netstat -ta Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 hyperion:ipp *:* LISTEN tcp6 0 0 localhost:ipp [::]:* LISTEN

</cli>

This command shows the list of all the active TCP and UDP ports on which the computer is listening.

Install, if necessary, the traceroute command then answer the following two questions.

Give the output of traceroute from your host to any host on one of the other ICCT networks.

Answer <cli prompt=“$” comment=“#”> user@hyperion:~$ traceroute hyperion

</cli>

Give the output of traceroute from your host to www.swan.ac.uk

Answer <cli prompt=“$” comment=“#”> user@hyperion:~$ traceroute www.swan.ac.uk # paste output here </cli>

Explain the result.

A new sub-network engineering-net (192.168.10.0/24) is to be added to the ICCT network. Host engineering (192.168.10.1/32) is a cluster server for this new network. Give the settings needed to set up this host as a router to icct-net, jupiter-net, and saturn-net and a gateway for engineering-net.

Answer

Which other files would you need to modify to correctly set up this new router?

Answer

Summarize the changes that you would you need to make to your host's network configuration to have the new engineering sub-network recognized?

Answer

Which other files would you need to modify to fully configure your host to recognizes the new engineering sub-network?

Answer

I hereby submit this work for marking.

Your signature here: B.A